Cutting discs online shop IE? Whether you’re a professional contractor or a DIY enthusiast and looking for a metal-cutting tool, this disc is a must-have. The cutting wheel is a great way to quickly cut through metal. With 52 wheels, you’ll always have one on hand. It is compatible with all 4-1/2 inch (115mm) angle grinders with 7/8 inch (22.2mm) arbor. The thickness of the wheel is 0.045 inch (1.2mm). You can operate this up to 13,300 RPM When it comes to precision and burr-free cutting, the Truswe Metal and Stainless Steel Cutting Wheel for Angle Grinder is tough to beat. This ultra-thin design delivers fast and accurate performance, with minimal material loss. The Metal Cutting Discs are made of aluminum oxide grains which are more safe than other wheel types. These discs should only be used when wearing all applicable safety gear because they can fly off the wheel and injure you if not careful. You should read the instructions before using this power tool. It is a heavy duty cutting disc that is fitted to any angle or side grinder. It will cut with ease through sheet metal, plastics, fiberglass, Plexiglas, ceramic tiles and even rubber. See additional details at welding supplies.
One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.
How to pick a welder tips: MIG wire inch button: A great feature. This will save you wasting your shielding gas when feeding wire through at the start of a new reel. Gas purge button: Another nice option. Save yourself some MIG wire, when you’re setting your gas flow. Burn back facility: Not all machines have this externally, buy it’s good to be able to trim the burn back to the wire according to the application & operator. Selecting the correct amperage machine: Generally, you should work on 35-40 amps per 1 mm diameter of material to be welded.
The Hobart Ironman 240 is the updated version to the Ironman 230 that recently has been discontinued. The 240 is a well-reviewed welder that delivers a wide range of power from 30 to 280 amps in a heavy-duty American-made chassis. Hobart equips the Ironman series with its “soft arc” technology for an easier striking, more spatter-free arc. If you are looking to weld aluminum, then like most of their MIG welders, they offer the package with a SpoolRunner 200 spool gun found here, for a few hundred extra bucks. This is a full-sized platform, offering a 15-foot gun connection and able to load a 44-pound spool of wire. Hobart backs the Ironman 240 with a strong five-year limited warranty. The power regulator has 12 notch settings for easy feel when setting the power level with gloves. This power regulator knob seems to be a problem for some users who have reported issues with the knob rotating freely and not changing the power setting. The only downside to this model is that it is unable to run directly off of a generator as it causes problems with the SCR firing timing of the welder. This makes it a bit less portable than some other welders, but nothing you can’t work around. Overall, this is a quality industrial-grade welder which is ideal for farm work which has been compared to Miller 252 – just without the digital screens and a few other features that most people wouldn’t need, but costs a lot less making it excellent value for the money.
A few advices on welding equipment, MIG and TIG welders, plasma cutters. Flat-Position Welding Increases Welding Speed : It’s common knowledge that welding in a horizontal position will be the easiest and fastest way to weld. A flat position is not as taxing to maintain and the welding puddle will stay in place. Take some time to evaluate each project before beginning in order to make sure the majority of welds can be completed in this position. If a job calls for vertical welding, see this article about vertical welding. Core Wire Feeder Increases TIG Welding Speed: For professional welders hoping to speed up TIG welding, a core wire feeder will add filler metal through an automated process. Watch this video on how it works. This enables welders to work with both hands and to maintain a constant flow of wire into the welding puddle. Ed Craig at the Frabricator writes about the wire feeder process first developed in Europe, saying it is “suitable for all-position welding on materials of any thickness, the process addresses traditional GTAW limitations and can enhance both manual and automated TIG weld quality and productivity.”
If you know that your new machine comes with a 2-year warranty, it can take a lot of the stress off your shoulders if your device suddenly stops working. If you can’t find a MIG welder with an appropriate warranty and the right features, it’s often a good idea to choose something that has spare parts which are easy to find. Try not to buy anything that’s made outside of the UK. The price range may be more affordable but the parts would be harder to source. Look for a spool gun so you can weld aluminium. If you plan on using your home welder to weld aluminium, then you’ll need a standard spool gun. Aluminium can quickly become damaged and tangled with a typical welding wire feed spool, so a spool gun will ensure that you can get the best results from your DIY work. Read additional info at https://www.weldingsuppliesdirect.ie/.
I’m a huge fan of Makita’s cordless LXT range. The DGA452Z is one of the best angle grinders available right now, and it’s a bit of a beast. The grip shape is nice and narrow, with comfortable rubberised overmoulding on the rear handle. Once you’ve installed a battery it’s well balanced and doesn’t feel too heavy at 1.3 kg without a battery installed. The Makita cordless grinder has a powerful brushless motor that’s efficient as well as powerful. It puts out a whopping 11,000 rpm, which is incredibly impressive for a cordless grinder. When you pair it up with a high Ah battery, it squeezes every last drop of power and runs for a surprisingly long time. It features a soft start function, battery gauge, and overload protection as well. There’s an anti-restart function for added safety between battery changes. One of the most impressive features must be the automatic speed control though. The internal computer controls the power output according to the load conditions, which makes for better cuts and longer tool life.
If you’re looking for the best portable weld fume extractor that would be small but powerful and also would come within an affordable price range, then BAOSHISHAN has the perfect device for you! This fume extractor absorbs all sorts of gases and dust generated by soldering and welding. The 1.2m smoking pipe is an added benefit to this fantastic device. Compact Design and Convex Tips. This small and compact machine has a state-of-the-art build quality that ensures high performance. The filters come with metal latches that seal off the fumes and don’t let any fume get out of the device. The pipeline’s sealing and stability are improved by fine convex tips. The machine comes with sturdy wheels that help to move the unit to anywhere you want. Its suction pipe is built with several small pipes which allow it to move around freely.
Hougen 115 volt hmd904 magnetic drill press is one of the best mag drill machine available in the market. And also the best thing is that Hougen upgraded this drill press recently. Thus it becomes more efficient and accurate from the previous one through their continuous development and innovative designs. New attachments of this great product are slot drive arbor, which not only enhances accuracy but also enhances the change-out mechanism. Drill bit also made with sturdy material. Cutter/Mount – Rota broach or Copperhead 3/4 inch shank. Thus it can make a smooth hole. This is great for horizontal, overhead, tight areas, and getting out of another piece of steel.
The ESAB group is owned by Colfax Corporation. Over 100 years after the company was founded, ESAB serves a global market for welding and cutting equipment. The group is organized in the regions Europe, North America, South America, Asia/Pacific and India. ESAB is represented in almost every country by subsidiaries or agents. Sales and support is established in 80 countries and there are 26 manufacturing plants across four continents. Visit the web site of your nearest ESAB office to find out more. Customers Talk, We Listen – The voice of the customer will always drive the development of our strategic plans and actions. Living this value is done by getting Customer Input and Expectations, at every opportunity, and by differentiating ourselves in How We Deliver to our customers. Innovation Defines Our Future – Individual and organizational creativity will drive breakthrough ideas for technology, products, solutions, and processes. We live this value by providing differentiated customer solutions, creating products and services that improve quality of life and environmental stewardship through Creative Thinking, and by understanding What Innovation Brings.
GPPH’s tables offer an incredibly stable and sturdy construction. The table top is made from 15MM thick material, this is outstanding when compared to the typical 6MM – 10MM that is usually used on lower end welding tables. In addition to this, the steel used is S355J2+N grade that is carefully selected. The steel is also unpickled so as to prevent the material becoming bright and causing arc to flash bounce off the table making the working conditions difficult for the welder. Finally, the tables are not coated with paint as it can make the surface difficult to conduct. They are coated with an oil based preparation which protects the tables during transport. Anti spatter is suggested.
If you’re a beginner welder but don’t mind splashing the cash for a top of the range welder, then try the Millermatic 141. Miller have really pushed the boundaries of usability with this welder and it features an auto-set feature for an easy set up, and infinite voltage and wire speed control. All you have to do is select the thickness of the metal you’re welding and you’re ready to start welding straight away. If you open up the machine you can tell that all the parts are great quality and really durable as well. There are more powerful welders on the market for the price, but there’s nothing better for welding up to 3/16 inch steel. See the full review here.
Sealey is one of the biggest manufacturers of tools and accessories in the UK, offering approximately 8000 items including tools for home, repair shops, agricultural facilities, as well as cleaning. In this variety, we found a gasless MIG welder MIGHTYMIG 100. The machine is able to weld metal sheets of a different thickness thanks to a toggle that allows setting the amperage to the minimum and maximum. The output range will be 55? and 100?, respectively. We should say that the welding time at the minimum power won’t be over 6 minutes. Yet, this welder will run for about 2 minutes at 90? and that’s great considering its moderate price. In addition, you’ll be able to manage the joint by varying the speed of the wire feed, just turn the relevant control knob to the desired setting. By the way, the welder is compatible with a flux-cored wire up to 0.9 mm, and the weight of the spool should be 0.9 kg. Like most welding tools, it features an overheating protection, and the orange light will notify you when the welder gets overheated after a long use. Apart from that, the forced air cooling system will chill the welder’s internal parts. The welder has a non-live torch for your convenience that will increase the accuracy of welding and provide safety.
United Kingdom market pick: Lincoln Electric is an Ohio-based company started all the way back in 1895. For over 120 years, Lincoln has produced some fine quality welders, and the Handy is certainly one of them. At about $300, this welder is a bargain while also offering great results. For around $200 dollars more than the $99 Goplus, users can expect an uptick in overall power and performance. As this Lincoln welder is well known for being both reliable and durable, welders who aren’t expecting an overabundance of power will love this machine. People who have purchased the Lincoln Electric K2185-1 Handy MIG welder remark that it is stable and long-lived even with daily use. The Handy Lincoln welder is able to weld mild steel from 24 gauge up to 1/8 inches thick. It has four output power settings that the user can dial in. The fan cooling system reduces the risk of it overheating.
Never drag, roll, or drop cylinders during the use. Always take care to maintain the valve caps during the transport. Avoid lifting the cylinder using a valve cap. Never store the cylinders for a long time period. Gas cylinders should only be purchased in small quantities. Never store them for long time periods. It is important to follow extreme precautions and safety measures while working with industrial gas cylinders due to several hazards and risks posed by them. Sourcing these cylinders from a reliable manufacturer is the most important safety measure for any facility owner using these cylinders.
